Spinning Upper Ball Joint - Jeep KJ and KK Liberty Forum.
How to tighten spinning ball joint.
Any Advice for Tightening Spinning Ball Joints? | Mazda World.
How to tighten a tie rod's ball joint without it spining.
How to Tighten a Ball Joint or Tie Rod End Castle Nut.
How to fix in place spinning steering rod ball joint - YouTube.
How Do I Torque a Spinning Ball Joint r/AskMechanics.
Help can't tighten the lower control arm ball joint bolt.
How To Tighten Ball Joints That Just Spin - EricTheCarGuy.
How to tighten the Ball Joints??? | ClassicB Forum.
How to tighten/remove spinning tie rod nut - YouTube.
Ball Joint Spins When Tightening Nut (This Is What to Do).

Spinning Upper Ball Joint - Jeep KJ and KK Liberty Forum.

Pull it apart, put the steering knuckle back in, put the jack under the lower ball joint and tighten the lower nut WITHOUT THE TOP NUT ON!!! Yes I'm yelling. If someone had posted that before I would have not wasted a few hours on the first side I re-assembled. Post back when you get it together. Dave Cool_Canuck Registered Joined Oct 17, 2003.

How to tighten spinning ball joint.

May 20, 2014 · How to tighten ball joints also works with tie rod ends or any other suspension part similar in design. The trick is to put the stud in a bind so that you can catch some threads, once you’ve done that and the fastener starts to tighten you can loosen up your ‘wedge’ and tighten it up the rest of the way..

Any Advice for Tightening Spinning Ball Joints? | Mazda World.

. Got them pressed in the knuckles, but how do you thghten the nuts if the studs rotate with the nut???? I see the "slot" on top of the stud, but what fits there, (if anything) to hold the stud? and how would you get a socket/torque wrench on the nut is using the slot? confused reamer.

How to tighten a tie rod's ball joint without it spining.

. Apr 15, 2018 · I always use a prybar and jam the stud back onto the spindle and hold it tight and whip the nut right off with an impact. Nuthin to it but to do it. I was putting the nut on. Still applies though! Like x 1 (You must log in or sign up to reply here.) Home. Every time I try to replace a ball joint, I get greatly frustrated because the ball spins with the nut, making tightening or removing the nut very difficult. Lots of aftermarket ball joints have wrench flats at the bottom of the stud. However it seems ones straight from the manufacturer come with a circular area instead that is not flat, so you can't get a wrench around it. So when removing.

How to Tighten a Ball Joint or Tie Rod End Castle Nut.

I usually use the floor jack to push the knuckle up to seat the ball joint taper. At that point, smack the back of the ball joint with a dead-low hammer to try and seat the taper tighter. Tighten the castle nut. The way yours is positioned, an impact wrench set on less that 1/2 of full torque can help snug it up... but don't over-do it. Just another day my lower ball joint broke so I had to remove all parts from driver side wheel steering mechanism. One of part was steering rod ball joint..

How to fix in place spinning steering rod ball joint - YouTube.

What you may need to do is place a support under the ball joint/control arm and let the car down enough to put pressure on the the system. You may need to whack the the spindle down so to create a binding pressure between the spindle and the taper of the ball joint. the impact gun is the best and easiest method I have used though. How do you tighten a ball joint that just keeps spinning? Just put a jack under the control arm to put some pressure on the joint to hold it solid while you tighten the nut. Thank you! Quoted From EricTheCarGuy: I sometimes take a pry bar and use it to 'wedge' the joint into the bore of the knuckle in order to hold it while I tighten it.. Oct 11, 2009 · Is there a trick to tightening the ball joint. it just keeps spinning - Answered by a verified Ford Mechanic We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.

How Do I Torque a Spinning Ball Joint r/AskMechanics.

.

Help can't tighten the lower control arm ball joint bolt.

Jun 16, 2022 · Easy little trick for spinning ball joint studs. Slide a bushing and cup pair up the bolt with the bushing#x27;s lip toward the bar. 9. Slide the spacer onto the bolt. Place a bushing, and then a cup, on the lower control arm where the link goes through it and slide the bolt through it. The lip on the bushing faces the lower control arm. 10.

How To Tighten Ball Joints That Just Spin - EricTheCarGuy.

Jul 29, 2013 · About $55. They call it the link rod, or something like that in their illustration, but it's the same part (also called the Leading Link). The new one did not spin, but for the old one, I used a big C clamp to get the old castle nut off. Tightened up the joint with the C clamp and was then able to get nut off. Put a small socket, wrench or even vice grips on the spinning end and continue away. Apr 3, 2005 #3 Bennett Active Member Administrator Joined Sep 8, 2004 Messages 5,387 Reaction score 2 Location Green Bay Yea, I ran into this problem before too. Basically I used a big "c" clamp to put press on it so it didn't spin. You can also use a pry bar..

How to tighten the Ball Joints??? | ClassicB Forum.

Jul 26, 2022 · Reason 3: Fuel Leaking from the Fuel Tank. When someone sees the ball joint spin when tightening, they always think of the shaft. In addition, some experts may also come up with the idea of lower arm control. But almost no one can understand that it might also happen for something silly.

How to tighten/remove spinning tie rod nut - YouTube.

A lot of times, when you're installing a ball joint into the lower control arm and trying to tighten the nut to lock in the ball joint shaft, the shaft will spin if you do not have enough pressure on the lower control arm. You will need to use a jack under the control arm as close to the ball joint as possible to push up on the joint so that the weight of the vehicle pushes the ball joint. Feb 21, 2006 · Yeah, the shank in the BJ can spin. But the receptacle in the spindle (that the BJ goes through) is tapered. So once you jack up the arm (which presses the shank into the spindle), the shank gets pressed in a bit and should stop spinning [enough to cinch it up]. It is for this reason that I recommend checking the big BJ nut after a few drives.

Ball Joint Spins When Tightening Nut (This Is What to Do).

Here I show you the simplest and safest way to torque your lower ball joint if/when if keeps spinning on you.SPECIAL TOOLS NEEDED:-Small floor jack. Ball Joints: Bottom: 70 to 90 ft. lbs. Put a jack under

How To Tighten Upper/Lower Ball Joint | GMC Truck Forum